These are small speakers with a big sound. Their size might lead you to think they are imaging champions with a limited maximum output and you’d be half right. Their imaging is near miraculous. If you close your eyes you really can’t tell where they are in the room. But despite their small size, just 33cm high, 20cm wide and 28cms deep, they can easily fill a big room. There’s obviously some pretty impressive technology at work here. Let’s take a look inside the box.
The front baffle gives us the first clue. The tweeter is a Jet III design, common to the majority of the ELAC range. This derives from Dr. Oscar Heil’s Air Motion Transformer, first introduced in 1993. It features a lightweight folded foil membrane driven by a magnet system of neodymium rods which provides high efficiency and strong dynamics. The bass/midrange driver is also unique to ELAC. It’s an 18cm AS-XR cone featuring a crystal membrane. The design is a recent refinement of ELAC’s AS aluminum-paper sandwich cone first introduced in 1993. More precisely the aluminum foil stamping is faceted like a gemstone rather than smoothly finished as in more conventional designs. This increases the stiffness of the cone, reducing resonances which results in lower colouration and increased dynamic range. The voice coil is attached to the rear paper cone and also to the bottom of the aluminum dome, a technique which ELAC says will increase the transmission range by a full octave. The rubber surround is wider than normal, allowing for a very long throw which provides high maximum sound pressure and smooth production of deep bass.
A quick glance will confirm meticulous attention to detail throughout the design of this speaker. For example, the four high quality binding posts at the back of each speaker are recessed and angled up for ease of access, the cabinet is exquisitely finished with rounded edges to reduce diffraction, and the stands are slim and elegant. They can sit happily on a carpeted floor or on a hard surface, offering both spikes and soft rubber feet in a fully configurable design. Fabric grills are supplied but the tweeters are protected from prying fingers so I left them off for best sound. They are very easy to fit, brass pins sliding into bushings and held in place by magnets.
The regular BS 244 runs $2,400 and comes in white or black high gloss. But the review pair is from the new upscale Black Edition which sells for $2,800. The Black Edition covers more than the cabinet and stand finish. It extends to a black finish for the crystal driver membranes and for the Jet tweeters. At rear the name plate is aluminum instead of just an adhesive label used on the standard edition. More importantly, ELAC has upgraded some parts for better sound. The wiring is now Val den Hul Skyline Hybrid, plus upgraded air cored foil capacitors and resistors in the crossover.
The speakers are pretty fussy about room placement, at least in my room. It took quite some effort to get them to show their full potential. I asked Bruno de Lorimier from Unison Sales Resources for help in stetting them up and he quickly found out why I was not hearing them at their best. Not only did I have them too far from the rear wall, but my demo pair was missing some accessories which would normally be in the box. Most importantly, there were no spikes, so I couldn’t get a strong coupling to the floor in my carpeted room. He also added a fabric dispersion control ring to the tweeters, which were otherwise a bit too lively in my setting, and he experimented with different port control inserts to optimize the bass response. Some speakers are a lot less fussy about setup, but the good thing is that ELAC supplies these multiple physical adjustment options in the box so you can get the best out of them in any room. Your dealer should be able to help you with this process or perhaps do the setup for you.
The BS 244 BE is a fairly sensitive speaker at 88 dB but it has a low impedance of 4 ohms which may be a problem for some amplifiers optimized for an 8 ohm load. ELAC claims a frequency range of 38 to 50,000 Hz, which compares favourably with other small speakers. The similarly sized Totem Ember ($4,200) which I enjoyed so much recently claims a bandwidth of 43 Hz to 25 kHz. Of course the ear cannot hear above 20 kHz so I wouldn’t start worrying just yet.
In case the name ELAC is not familiar to you, I should add that the company is based in Kiel, Germany where all their speakers and drivers are made. The company can trace its history back to 1926 when it began research into sonar technology and the passage of signals and sound through air and water. Loudspeakers became their focus in 1985 and their exclusive domain in 1997. Their six strong development team is led by Rolf Janke.
Once properly set up, I could now focus on the listening. I paired the speakers with a Meridian G08 CD Player, an EMM Labs Pre 2 preamplifier and the powerful KWA 200SE Power Amp from ModWright, linking them all with Nordost Valhalla cables. Bruno positioned the speakers about 8 feet apart and just under a foot from the rear wall, well away from corners. He inserted a hollow foam ring into the rear port as well as the tweeter dispersion ring for best sound. Several characteristics were immediately obvious. First the tweeter is indeed exceptionally smooth and extended, with an enormous capacity for peak loads. Your amplifier will give up before the speakers will. Second the speaker has been designed to be as uncoloured and neutral as possible. Thirdly it throws a really big image, which together with its considerable bass extension makes you think you are listening to a much bigger speaker.
Advertisement: Shop for ELAC loudspeakers at the CANADA HiFi Shop (novo.press/shop).
About the Author: Phil Gold
